Knuckle Joint Press Kieserling & Albrecht KKPR 2000/1000
TypeKnuckle Joint Press
Nominal force2000 ton
LocationEurope
StatusHot offer
Used Industrial Equipment · Poland, Europe
Used 2000 Ton Presses for Sale
2000-ton presses come in two types: knuckle joint for coining, sizing and cold forging, and hydraulic for deep drawing, forming and straightening. The Kieserling & Albrecht KKPR 2000/1000 knuckle joint press is available now. Our Dnepropress D2243 hydraulic press reference is sold; we source similar hydraulic units through a partner network across Europe on request.
2000 ton Hydraulic Press Dnepropress D2243
TypeHydraulic Press
Nominal force2000 ton
LocationBalti city, Moldova
StatusSold
What 2000 Ton Capacity Means in Practice
Coining, sizing and cold forging
A 2000-ton knuckle joint press delivers peak force near bottom dead centre for coining, sizing and precision cold forging of large steel components. The Kieserling & Albrecht KKPR 2000/1000 runs a 140 mm stroke and 510 mm shut height at up to 40 strokes per minute, built for this class of work.
Deep drawing and large panels
A 2000-ton hydraulic press gives controlled load for deep drawing and forming large sheet or plate parts. The Dnepropress D2243 example had a 1400 mm slide stroke, 2400 mm daylight and a 1650×2000 mm table, enough room for tall tooling and large panels.
Straightening heavy parts
The hydraulic class suits straightening shafts, welded structures, frames and heavy fabricated parts. The long hydraulic stroke helps the operator approach the part under control and apply load where it needs correction.
Composites, rubber and pressing work
Hydraulic presses in this range handle pressing processes that need dwell time, controlled speed and repeatable force. Composite panels, rubber products and thick assemblies often need this type of pressure profile.
Two Machine Types at 2000 Ton
The 2000-ton machines TRIGA has offered serve different processes. The Kieserling & Albrecht KKPR 2000/1000, available now, is a knuckle joint press built in 1960 with a 140 mm stroke and 510 mm shut height, running up to 40 strokes per minute; the toggle drive concentrates peak force near bottom dead centre, suited to coining, sizing and precision cold forging. The Dnepropress D2243 hydraulic press, sold, had a 1400 mm stroke, 2400 mm daylight and a 1650×2000 mm table, built for deep drawing, forming and straightening over a long working stroke. The process decides which type fits: short-stroke precision work on the knuckle press, or long-stroke forming and drawing on a hydraulic press.
Transport and Installation at This Scale
Machine weight
Weight at 2000 tons varies by machine type and construction era. Our sold Dnepropress D2243 hydraulic press weighed 144.5 tons; the Kieserling & Albrecht KKPR 2000/1000, a compact 1960s knuckle joint design, is lighter. TRIGA confirms exact weight and dimensions during technical evaluation.
Oversized transport
Main components normally move as OOG cargo at this tonnage. The project needs a route survey, permits, lifting plan and the correct crane capacity before dismantling starts.
Foundation
A 2000-ton press needs a foundation designed from the manufacturer's drawing, hydraulic or mechanical alike. Anchor layout, pit depth and upkeep access all need review before installation; a knuckle joint press also needs foundation stiffness against cyclical impact loading at bottom dead centre.
What to Check at Inspection
Toggle pins and clutch (knuckle joint)
On a knuckle joint press like the KKPR 2000/1000, measure toggle pin and bushing clearance and verify clutch engagement angle. Worn pins cause load eccentricity and die misalignment in coining and sizing work. See our knuckle joint press inspection guide for the full checklist.
Cylinders and seals (hydraulic)
On a hydraulic press, inspect the main cylinders, rods and seals for leakage, scoring and uneven movement. Oil leaks under load usually point to seal work or cylinder repair.
Slide guides
Measure slide guide wear and check whether the slide travels squarely, on either press type. Large tables and off-centre loads make guide condition important at 2000 tons.
Electrical controls
Review the electrical cabinet, operator controls, limit switches and pressure or clutch control circuits. Older controls often need renewal before production use.
FAQ
Frequently Asked Questions
Yes. The Kieserling & Albrecht KKPR 2000/1000 knuckle joint press is available now, with full specifications listed above. Our Dnepropress D2243 hydraulic press reference is sold; send your tonnage, table size, stroke and process requirements and we will search for a similar hydraulic press through our partner network across Europe.
It depends on the type. The Kieserling & Albrecht KKPR 2000/1000 knuckle joint press, available now, handles coining, sizing and precision cold forging. A 2000-ton hydraulic press, like our sold Dnepropress D2243 reference, handles deep drawing, forming large panels, straightening and open-die work on bulky parts.
A knuckle joint press like the KKPR 2000/1000 delivers peak force near bottom dead centre and runs a short stroke at moderate speed, suited to coining and sizing. A hydraulic press applies full load through the whole working stroke and lets the operator adjust speed and dwell time, which suits deep drawing, forming and straightening on larger, longer-travel parts.
It depends on the machine type and era. The Dnepropress D2243 hydraulic press we sold weighed 144.5 tons. The Kieserling & Albrecht KKPR 2000/1000, a 1960s knuckle joint design, is a lighter, more compact machine; TRIGA confirms exact weight during technical evaluation.
Yes. The Kieserling & Albrecht KKPR 2000/1000 is available for on-site inspection now. Running tests depend on the electrical connection at the site. Send your technical requirements and we will confirm what can be checked on a specific machine.
A 2000-ton press is dismantled into main assemblies, lifted with suitable cranes and shipped as oversized cargo. The work plan covers route survey, permits, loading, export documents and installation data based on the manufacturer's drawings. Scope depends on the specific machine's weight and dimensions.
Contact Us
Looking for a specific machine?
Send us your specifications and we will advise on availability, inspection options and delivery.
Email
info@trigapl.com
Phone / WhatsApp
+39 331 780 4001
WhatsApp
+48 570 337 352
✓ Response within 24 hours · EN / IT / PL